Ashley AP5660L Spezifikationen PDF herunterladen (Seite 11)

INSTALLING YOUR ROOM HEATER

You have already made the important decision of choosing your U.S. Stove Pellet Burning Room Heater; now your next step

is to determine where to install your new pellet stove heater. To get the most efﬁ cient use of re-circulated heat, you should

consider a room that is centrally located within your home. Choose a room that is large and open.

It is Extremely Important to maintain proper clearances from any combustible surfaces or materials in the room where your

heater will be located. You can ﬁ nd proper clearance measurements on page 10 of this manual and on the rating label

of your pellet stove.

The pellet stove can be vented through an exterior wall or into an existing masonry or metal chimney. The chimney must

be lined if it is over 6” (150mm) in diameter or if it has a cross-sectional area of over 28 square inches (711mm2). Venting

can pass through the ceiling and roof if approved pipe is used. Where passage through a wall, or partition of combustible

construction is desired, the installation must conform to CAN/CSA-B365

DO NOT OBTAIN COMBUSTION AIR FROM THE ATTIC, GARAGE OR ANY OTHER UNVENTILATED AREA. YOU MAY

OBTAIN COMBUSTION AIR FROM A VENTILATED CRAWLSPACE.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER HEATER, FURNACE OR APPLIANCE.

INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.

ONLY USE APPROVED MATERIAL FOR INSTALLATION, FAILURE TO DO SO MAY RESULT IN PROPERTY DAMAGE,

BODILY INJURY, OR EVEN DEATH.

This appliance is certiﬁ ed for use with listed 3 inch or 4 inch “PL” or “L” pellet venting products as well as Selkirk’s Direct-

Temp Vent system for pellet burning appliances. The use of other components other than stated herein could cause bodily

harm, heater damage, and void your warranty.

HORIZONTAL EXHAUST VENT INSTALLATION

1. Locate your pellet stove in a location which meets the requirements of this manual, but in an area where it does not

interfere with the house framing, wiring, etc.

2. Install a non-combustible hearth pad underneath the pellet stove. This pad should extend at least 6” (152mm) in front

of the unit.

3. Place the pellet stove approximately 15” (381mm) away from the interior wall.

4. Locate the center of the exhaust pipe of your unit. This point should then be extended to the interior wall of your house.

Once you have located the center point, on the interior wall, cut a 7” (175mm) diameter hole through the wall.

5. The next step is to install the wall thimble, refer to the instructions which come with the wall thimble for this step.

6. Install the appropriate length of exhaust vent pipe into the wall thimble. See steps 11 and 12 when determining the cor-

rect length of exhaust vent to use.

7. Outside Fresh Air is Mandatory when installing this pellet stove room heater in airtight homes and mobile

homes. Be sure that the outside air vent has an approved cap on it to prevent rodents from entering. Be sure to install

in location that won’t become blocked with snow, etc.

8. The air intake pipe is equipped with a butterﬂ y valve that is preset to maximum air intake. For optimum operating ef-

ﬁ ciency you may calibrate the butterﬂ y valve to provide less intake air. (See Figure 7) Caution: Too much restriction

on the intake air will cause dirtier burn, therefore, will require more frequent cleaning.

9. Connect the exhaust vent pipe to the exhaust outlet of your pellet stove.

10. Secure all vent joint connections with 3 screws. Seal the exhaust vent joint connections with high temperature silicone

sealant.

11. Push the unit straight back to the interior wall, being sure to maintain the minimum clearances to combustibles 6”

(152mm) to the back of the unit. Seal the annular space of the wall thimble and around the vent pipe with high tem-

perature silicone sealant.

12. The exhaust vent pipe must extend at least 12” (300mm) out past the exterior wall. Seal the annular space of the wall

thimble and around the vent pipe with high temperature silicone sealant.

13. Install an approved horizontal termination cap or if necessary install a 90° elbow and appropriate length of vertical vent-

ing. An approved vertical vent cap is recommended.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Ashley AP5660L Spezifikationen Seite 11

Kommentare zu diesen Handbüchern